Відео

Thanks 🙏

The clamps that came with my set seem to be too big. Even when fully closed there's about a centimeter of space. Does the rubber cover stretch out a lot to make up for this?

So if my key is faulty would the immobiliser lock my thob will open and lock the car. I have error 161600 161450 been told all kinds of rubbish

Your supposed to remove the paint on the contact area of the disc so the paint will not contaminate the new pads.

Great vid btw!

Come on, you took the first rattling sound from 2.0 tfsi ea113 VW engine :D

Great video, thanks!

Nice instructions! as technician, I appreciate your effort 👌

Good tutorial buy you don't say what size sockets you need

very useful ,thank you

They said the injectors were defective, we had them repaired and the problem still did not go away. If this is the only reason, I will be grateful to you. Greetings from Turkey.

Whats diameter of for wheel 2009 insignia 29,4 or 29.6 or 30.2 ???

I have electronic parking break and I reactivated them with one them still not on the rotor and the piston came out completely. I'm hoping that with this video I will be able to push it back in using your method.

Nice vid, best I've seen.....however, can anyone explain to me how, in normal operation, the brake pad is released from the disc? It's obvious that when the brake is applied (both by foot and by motor) the caliper pushes against the pad but what happens when the brake is not used.....what pulls the pad back off the disc. There is no mechanical means of pulling it back off.....does it simply rely on nil pressure resulting in the the pad being in constant contact (just touching) the disc? Please help as my brain hurts 🙂👍

Witam Jakie uszczelki trzeba kupić bo szukam i nie ma kompletu zestawu Hello What gaskets do I need to buy if I am going to assemble after cleaning

Gr8 idea. Cheers Graham

So many lubricants... I mean... is it crucial they are not all just grease?

I have the same exact problem misfire on injector 4 i switched him with injector 1 and i still got the same problem with cylinder 4 misfire now what else could possibly be the problem please i need help before i tear down the engine for the hydraulic lifters and valves

Great Engineering! Any recommendations on Amazon for the best model blaster?

Really good job bro, well done

The handbrake should be pulled up or no?

Fantastic video, very informative and detailed, thankyou :)

Thank you very much for this excellent video !!! It has made me confident to start doing it myself . I did it on a complete week-end including the cleaning with pure acetone. The warning light, so annoying, no longer reappears at all after the reset with my OBD2 reader. The car is now more punchy, consumes 0.5 liter less per 100km and I saved a lot of money :-) the garage did not want to clean but to put new parts.. Several points to share if it can help : - XC60 2014 200K km - EGR changed at 60K km - EGR recall done ~2years ago (hoses +ECU reprog it seems)- motor warning light appeared 6 month ago - I've bought the gasket between EGR and cooler on auto-doc Ref 013.630, brand 'Elring'. It fits perfectly and is of good quality - Step to empty the coolant at 4:50 in the video skiped. I used a cut bottle instead to recover the liquid (~0,5 liter) when removing the hoses. - the tightening torques can be found on other videos- the step of unscrewing the 2 screws between the EGR and the exhaust pipe is not shown in the video ~6:22. Have you changed your original torx bolts to new ones in yellow color (hexagonal head) ? On my car it has torx screws and I had a problem at this step because I stupidly forced with a Torx30 screwdriver even though it was Torx40. I couldn't see the screw well because the head was oriented towards (and close to) the dashboard; I partially broke the teeth of the screw. I recovered the problem by forcefully pushing a torx40 screwdriver into the screw (with a hammer), it worked. Voila ! Thanks again and long life to your channel ! ;-)

good video

kia service

Hello, I have fault code P2262, on volvo xc60 2015 2.0 diesel. I have already change 2 sensors but the problem is not gone. Can same one help

Este foarte detaliat 10 nota,puțini știu a face un tutorial.Din cît se vede astai profesia din vare faci banii

I have the same car. What sensor did you buy? Do you have the reference? Thank you

What mileage should fuel filter be changed

Hi can use this step when immo. Active car not crank

Thanks for sharing 😊

excellent vid thanks

Awesome video! Very helpful, perfect amount detail/explanation (not like others who “like sound of own voice” too much and blabber on). Like it 👍

Hi, I have a something problem same for my Vauxhall Xenia 2014 1.8 I put the key inside he knows start you can have a solution

Now any insight on doing this on a VW Atlas? The shaft inside has a lot of tiny little balls and springs that dislodged itself on me. I think I have to just buy new calipers, it doesnt look like I can re assemble this thing!

Love this !!! simple, economical, and functional!. thank's ! as an improvement, we could suck the sand directly from the box with a hose! ;)

Hi there, you sure help me a lot whit this content, I've just have done replacing the wire loom on my 1.9 tdi, the 1st injector was like a mad drunk guy on a psy transe after party. Thank you very much 🙏🏽🙌🏽👌🏽

Great job...really excellent video

Nice video bro, lots of good info, a common sense approach and it's plain to see you know your onions 👍👍👍

Thanks

Just a heads up to anyone trying this. The wee screw that holds the disc on is made of chewing gum, not metal it seems. I’m now stuck trying to figure this headache out 😂

Vire nice

This video saved me big time. Thank you for sharing your experience!!!

How does the fuel tank not drain when fuel line removed

Here in 🇮🇳 i got it done for £44 in my polo 6R

You saved me with The reassembly!! Thank you!!!!

Thank you!

This is the best video for us beginners, everything is clear. Thank you bro

Can’t we access from driver side bottom of the car by removing bottom protection plastic/or whatever there.

Truth about all these caliper painting videos. If you don’t have an access to a send blaster, don’t even think about painting your calipers! And if you think you can do a good job with a wire wheel attached to your drill? Well, good luck with that!😂